TO/GA Party! How Go-Arounds Work

Why and how pilots go-around

AeroSavvy - TOGA Party: How Go-Arounds Work Go-around

Spend time at a busy airport and you’ll likely see an aircraft go-around. Find out why airplanes go around and how the maneuver enhances safety.

Terminology

Go-Around terminology can be confusing. There are a few terms different terms used (and misused), so let’s clear things up!

Go-Around

Go-around is the general term used when pilots discontinue a landing. The maneuver can be accomplished anywhere along the final approach course and even after the aircraft touches down on the runway.

During a go-around, the crew will climb the aircraft and follow instructions of air traffic control. In addition, they may fly a published missed approach procedure (a charted route) that will guide them safely away from terrain and other air traffic.

AeroSavvy - TOGA Party: How Go-Arounds Work Go-around

“Go-around” is also the standard international terminology used for communication between pilots and controllers. Example: “Aerosavvy 101, zombies roaming the runway. Go-around.

Why are they called Go-Arounds?

Aircraft at smaller airfields typically fly a rectangular traffic pattern (or circuit) around the runway in preparation for landing. If the pilot decides not to land, the aircraft climbs and rejoins the pattern to go around the circuit and make another approach. Although airliners rarely fly a traditional traffic pattern, the maneuver is still called a go-around.

AeroSavvy - TOGA Party: How Go-Arounds Work Go-around

Rejected or Balked (Baulked) Landing

A rejected landing is a go-around that begins at very low altitude after the pilot has made the decision to land.

In some cases, an aircraft will actually touch down on the runway during a rejected landing. There are situations where getting the aircraft back into the air is safer than completing the landing.

The terms rejected landing and balked (baulked in the UK) landing are essentially interchangeable. Usage and precise definitions vary by region. Aviation regulators (FAA, EASA, etc) and aircraft manufacturers use the term “balked landing” when discussing aircraft performance requirements during low altitude (or after touch down) go-arounds.

Other Go-Around Terminology

AeroSavvy - TOGA Party: How Go-Arounds Work Go-aroundNavy aircraft use different terms for go-arounds and balked landings.

  • Wave Off – When the Landing Signal Officer orders a pilot not to land on the aircraft carrier, it’s called a wave off. Similar to when an air traffic controller orders an aircraft to go-around.
  • Bolter – A carrier landing attempt in which the tailhook fails to engage an arresting wire, requiring a go-around. This is similar to a balked landing.

Until a few years ago, U.K. Royal Air Force controllers would order a pilot to “Overshoot” when a go-around was necessary. A few pilots tell me that “overshoot” is occasionally heard in Canada. “Go-Around” is now the standard international phraseology.

Canadian air traffic controllers will sometimes order a crew to: “Pull up and go-around.” I suspect the “pull up” part is an attempt to get the pilots moving in the right direction while they think about the go-around. 🙂

In the UK, when ordering a flight to go-around, controllers state:
“AeroSavvy 101, go-around, I say again, go-around. Acknowledge.” The controllers want to make certain the pilots hear and confirm the order.


Pilots & Controllers: If you’ve heard other phraseology used for go-arounds, I want to hear about it in the comments below!

Missed Approach

The term missed approach is often incorrectly used to describe a go-around. The terms are not interchangeable. A missed approach is a published instrument procedure that begins after the go-around is initiated.

When pilots fly an instrument approach to a runway, they follow a detailed route displayed on an approach chart. If the pilots are unable to land when reaching the runway, they perform a go-around. The crew will follow a Missed Approach Procedure on the approach chart that guides the aircraft safely away from terrain and other air traffic.

If a crew needs to abandon an instrument approach, they will alert the controller: “Metropolis Tower, Aerosavvy 101 is going-around.” Tower will then provide guidance. They might give the crew a specific heading and altitude, or say “AeroSavvy 101, fly the published missed approach.” The latter instructs the crew to follow the published missed approach procedure on the chart.

Subscription Form

The image below shows an approach chart for Singapore’s runway 20C. The image on the right is the same procedure displayed on a 767 navigation screen. The Missed Approach Procedure (MAP) is highlighted in yellow. For more about pilot charts and navigation, read: How do pilots find their way?

AeroSavvy - TOGA Party: How Go-Arounds Work Go-around
Singapore runway 20C approach chart and the same approach on the aircraft navigation screen. The missed approach procedure is highlighted in yellow. Click for larger image.

To summarize: When pilots on an instrument approach are unable to land, they will go-around, then fly a published missed approach procedure or follow the controller’s instructions.

AeroSavvy - TOGA Party: How Go-Arounds Work - Go-around
An A320 goes around due to an A340 on the runway. Used with permission: Tim BowreyJetPhotos.com

A Go-Around Is Not an Emergency

When pilots go-around, they are avoiding a potentially hazardous situation. Flight crews are encouraged to go-around any time they are uncomfortable with an approach or landing. There are no penalties or paperwork involved when a pilot chooses to discontinue an approach.

When in doubt, Go-Around!

Excellent guidance for every pilot, regardless of experience level and equipment.

 Why Do Pilots Go-Around?

There are several reasons why a pilot or air traffic controller may want an aircraft to go-around.

  • Unstable approach – Most airlines require aircraft to be stabilized by 1000 feet (about 3 miles from the runway). A stabilized approach means the aircraft is at final approach speed and fully configured with landing gear and flaps extended. Studies have shown that unstable approaches are a causal factor in many landing accidents. If the aircraft isn’t stable by 1000 feet, a go-around is usually required.
  • Spacing/Separation – Air traffic controllers try to keep landing aircraft separated by 3-5 miles. This gives an aircraft enough time to land and exit the runway before the next aircraft lands. If spacing becomes too close, the tower controller can order a flight crew to go-around.
  • Stuff on the Runway – Ground vehicles, aircraft, trash, and animals on a runway will cause pilots to go-around. Animals? Dogs, deer, moose, foxes… even turtles and frogs have caused pilots to go-around!
  • Aircraft Mechanical Problem – Although rare, a flight crew might discover a mechanical problem on final approach (perhaps a flap or landing gear issue). Going around will give the pilots time to troubleshoot the problem so they can return for a safe landing.
  • Weather Below Minimums – Instrument approaches often specify a decision altitude where the flight crew must see the runway to land. If the pilots are unable to see the runway when the aircraft reaches decision altitude, they perform a go-around.
  • Ugly, Nasty Weather – Gusty winds or turbulence can make landing a real challenge. Wind shear (sudden change in wind speed or direction) or other severe weather can cause a flight crew to go-around. Pilots use on-board weather radar and wind shear detection equipment to aid in making the land or go-around decision. Here is a video demonstrating predictive wind shear warning technology on a Boeing 767. Pilots test this equipment daily.

How Do Pilots Go-Around?

The go-around is a safe and smooth maneuver that airline pilots practice in the simulator. A go-around early in the approach phase will often go unnoticed by passengers.

Specific procedures vary by airline and aircraft type. Different planes have different buttons, procedures, and terminology. The following is a generic go-around procedure for an AeroSavvy Airlines Boeing 767 (flown by our best crew).

The go-around begins 100 miles from the airport.

About 100 miles from the destination, a flight crew will do an approach briefing. They spend a few minutes reviewing airport-specific charts and procedures necessary for landing. Arrival routing, updated weather, runway conditions, and taxi routes are discussed.

Finally, the crew reviews the go-around and published missed approach procedure for the expected runway. We always plan for a go-around.

Let’s get out of here!

We’re on final approach and Metropolis Tower has cleared us to land. The runway lights are in sight!

As we descend below 200 feet, we hear our call sign on the radio:

AeroSavvy 101, Metropolis Tower. Aircraft on the runway. Go-around. Fly the published missed approach.”

The crew responds: “Metropolis Tower, AeroSavvy 101 going around. Flying the published missed.

Go-Around Procedure

A well-rehearsed, scripted procedure now takes place on the flight deck. The script is spoken out loud as the crew performs the actions.

AeroSavvy - TOGA Party: How Go-Arounds Work Go-around
Depressing either switch on a 767 activates Go-Around mode. Autothrottles provide go-around thrust and the flight director gives the pilot (or autopilot) pitch up guidance for the climb.  Click for larger image.

PF=Pilot-Flying
PM=Pilot-Monitoring

  • PF: “Go-Around Thrust”
    The pilot-flying presses one of the go-around switches on the thrust levers. This signals the autothrottles to advance to go-around thrust and places the flight director in go-around mode to provide pitch guidance for the climb. The pilot-monitoring confirms the thrust levers advance to go-around power.

    The pilot-flying (or autopilot) begins to pitch the aircraft up to begin the climb.
  • PF: “Flaps 20”
    Pilot-monitoring selects flaps 20. This retracts the flaps from the landing position to the go-around position.
  • PM: “Positive Rate”
    Pilot-monitoring confirms the aircraft is climbing and says “Positive Rate.”
  • PF: “Gear Up”
    Pilot-monitoring positions the gear handle up to raise the landing gear.
  • At 400 feet above ground, the pilot-flying calls: “LNAV” (pronounced el-nav).
    Pilot-monitoring activates the flight director system’s Lateral Navigation (LNAV) mode. This provides the pilot-flying (or autopilot) guidance to fly the programmed missed approach procedure.
  • At 1000 feet above ground, the pilot-flying accelerates the aircraft and calls for the flaps to be retracted.

That’s it! The crew will continue to fly the published missed approach procedure until the air traffic controller decides how to merge the aircraft back into arriving traffic. In most cases, controllers will immediately issue heading and altitude instructions.

This fun dance happens a few times every day at busy airports all over the world.

Here’s a 2-minute video demonstrating what a go-around looks like on a Boeing 757 & 767 Electronic Attitude Direction Indicator (EADI):

What does “TO/GA” mean?

AeroSavvy - TOGA Party: How Go-Arounds Work Go-around
Embraer ERJ-175 Regional Jet thrust lever TO/GA position.

Many high performance aircraft have a switch and/or thrust lever position labeled “TO/GA.” This odd assortment of letters is an acronym for TakeOff/Go-Around (pronounced “toga,” like the ancient Roman garment).

The exact function of the TO/GA switch varies on different aircraft models. In general, the dual-function TO/GA switch signals the autothrottles and flight director to provide takeoff thrust and guidance when on the runway, or go-around thrust and guidance when on an approach.

TO/GA PARTY!

AeroSavvy - TOGA Party: How Go-Arounds Work Go-around
Roman Emperor Antoninus Pius couldn’t fly an airplane, but he was always ready for a TO/GA party!

Go-Around Switches and Thrust Lever Detents

Here’s a gallery of Go-Around and TO/GA buttons. Different aircraft manufacturers have different philosophies about the best way to trigger a go-around. Boeing, Embraer, Gulfstream, and a few others prefer a button or switch. Newer Airbus aircraft have a thrust lever detent (position) that triggers the go-around mode. Pilots are usually trained and assigned to one aircraft, so they don’t have to worry about getting confused. Although I fly both the Boeing 757 and 767, they have identical cockpits so the procedure and button positions are the same.

This slideshow requires JavaScript.

Go-Around From the Passenger Seat

The go-around is easy for the people in back. Many passengers don’t even realize they’ve done one! Here’s what to expect if your flight crew needs to perform a go-around:

Approaching the airport for landing, passengers usually hear a flight attendant chime (ding-ding) followed by an announcement to fasten seat belts and assure tray tables are in the upright position. If all goes well, the aircraft will land in the next 5-10 minutes.

If the flight crew needs to go-around, they won’t have time to tell the passengers (they’ll be quite busy). The first indication the aircraft is going-around is the sound of the engines increasing thrust. The aircraft will pitch up slightly and begin a shallow climb, followed by the sound of the gear being retracted. The crew will then retract some or all of the flaps.

The plane will make a few turns then fly 5-10 miles downwind before lining up with the runway for another approach. The crew will extend the flaps and landing gear back to landing configuration.

A go-around will add 15-30 minutes to the flight, depending on airport traffic. Think of it as a free sight-seeing excursion, courtesy of your airline!

AeroSavvy’s Final Thought

To my friends, colleagues and followers who are pilots, I’ll leave you with this final thought: You Can Always Go-Around!

Trivia about the music video: 40 seconds into the video is the famous clip of a UPS DC-8 battling the Santa Ana winds in Ontario, California. A strong gust of wind hit the aircraft just moments before touching down and the crew elected, wisely, to go-around. This event happened long before the days of cell phone video. The go-around was captured by a video crew awaiting the arrival of an aircraft carrying race horses. They decided to shoot test footage and along came the DC-8!

Photo Credits

Thank you to the aviation pros whose photos are used in the article. If you’re looking for AvGeeks to follow, check out their Twitter feeds!

18 Comments

  1. Thanks AeroSavvy! My first love and profession is meteorology, but aviation is right up there. The details you provide and coverage of multiple aircraft is a bonus.

  2. Captain H.
    Once again your posts offer interesting, informative and detaiedl insight with a touch of humor.
    God keep you safe as you slip earthly bonds.

  3. Enjoyed the post! It’s interesting how the go around procedure is pretty much the same for all aircraft. Hit “toga”, pitch & power up, flaps come up a notch, positive rate, gear up, select or confirm lateral and vertical navigation modes, etc.

    P.S. You can’t ALWAYS go around (a little something I learned from flying gliders 😉

    • So true! Every plane needs just about the same sequence of stuff to happen to safety go-around.

      As for gliders… OK; you can (almost) always go-around!

      Ken

  4. I’m so, so, so excited I found your website! I’ve been binge-reading articles for the past few hours. Great reporting!!!
    Slightly off topic but have you ever done an article about the different cockpit controls? How hard it is to adapt from Boeing controls to Airbus sidesticks etc.?

    • Hi Alina,

      I’m glad you’re enjoying AeroSavvy! I haven’t done an article comparing different flight controls, but it’s a good idea. I have friends that transitioned from Boeing, McDonnell-Douglas, and regional jets to the newer Airbus aircraft. They tell me the sidestick control is very intuitive and they really enjoy flying the aircraft.

      Thanks for reading!
      Ken

  5. One thing that usually strikes me is how matter of factly and nonchalantly go arounds are mentioned on the radio, especially by pilots (ATC is often a little bit more excited, particularly if they are ordering the go around). “American 123, going around,” is typically said by pilots with less excitement in their voices than you hear them use when ordering their coffee at the airport Starbucks.

    The VASAviation channel on YouTube (no affiliation) has some great examples of this in the videos they post, and the radars and animations synched to the ATC recordings really show how skilled and professional pilits and ATC are, especially after a go around is required at a busy airport like JFK.

    • Right! Pilots practice go-arounds almost from the first flying lesson. Every student pilot who solos (typically 14-20 hours of flight time) knows how to do a go-around. It’s one of the fundamental skills pilots learn.

      Thanks for reading!
      Ken

  6. Ken,
    Interesting article, just what I’ve been looking for in my research, Could you clarify something for me?
    With aircraft that have TO/GA switches, does pushing these make the AP commence the procedure? (in relation to China Airlines 140 (Airbus A300)). I ask as I am writing a paper in psychology of decision making and I need to understand the procedure better.
    Thanks.

    • Hi Ben,

      That’s a difficult question to answer. Different aircraft manufacturers have different philosophies about how automation should work. In general, if the autopilot is engaged, pressing the go-around switch on most planes would begin an autopilot go-around. I’m sure there are exceptions.

  7. Every time I check out your website always find more to learn. Even checked out some articles several times, like how on earth pilots understand what all the different colored night lights on a runway mean. There are a few news articles out about letting the aircraft fly by themselves. No way I would get on one, I want the extremely well trained pilots and co pilots out front. Always thank the flight crew for a safe flight when getting off.

Don't just sit there... Say something!

This site uses Akismet to reduce spam. Learn how your comment data is processed.